ODROID-H3 / H3+ Supply

Description

ODROID-H3 / H3+

ODROID-H3 and H3+ have the same form factor and similar power efficiency as their predecessor, the ODROID-H2+. However, the H3 and H3+ are more powerful, offering higher performance. You’ll need to supply your own memory and storage (check the recommended accessories on this page) — but since the ODROID-H3 family uses the same components commonly found in modern laptops, you should have no trouble finding compatible hardware to fill out your SBC.

ONLY NVMe M.2 SSD ARE COMPATIBLE: PCIe NVMe M.2 SSD

Both models of ODROID-H3 feature two SO-DIMM slots for memory, two SATA ports and one M.2 NVMe slot for storage, two 2.5 GbE ports, two USB 3.0 ports, two USB 2.0 ports and more!

• ODROID-H3: Intel quad-core Jasper Lake N5105 processor
• ODROID-H3: Intel quad-core Jasper Lake N6005 processor

Additional items required to operate – see “REQUIRED ITEMS” section below.

KEY FEATURES

• SoC:
• H3: Intel Jasper Lake N5105 quad-core processor, base clock of 2.0GHz and boost up to 2.9 GHz
• H3+: Intel Jasper Lake N6005 quad-core processor, base clock of 2.0GHz and boost up to 3.3 GHz
• GPU:
• H3: Intel UHD Graphics 24 EUs Turbo 800MHz
• H3+: Intel UHD Graphics 32 EUs Turbo 900MHz
• System Memory – Dual-channel Memory DDR4 PC4-23400 (2933MT/s) supporting up to 64GB RAM in total
• Storage – M.2 PCIe 3.0 x4 slot for one NVMe storage, 2x SATA 3.0 ports, eMMC flash support
• Video Output
  • HDMI 2.0 up to 4K (4096×2160) @ 60 Hz
  • DisplayPort 1.2 up to 4K (4096×2160) @ 60 Hz
• Audio – HDMI, audio jacks for HP, MIC. and S/PDIF
• Connectivity – Dual 2.5 Gigabit Ethernet (RJ45)
• Expansion – 24-pin header with I2C, UART (3.3V), USB2.0 and HDMI CEC signals
• SSE4.2 accelerator (SMM, FPU, NX, MMX, SSE, SSE2, SSE3, SSSE3, SSE4.1, SSE4.2, AES)
• A configurable Unlimited Performance mode allowing the CPU to run in sustained turbo boost mode
• Misc – RTC battery (Included)
• Power Supply – 14V to 20V DC power input
• Dimensions – 110x110x43mm
• Weight – About 320 grams with heatsink, two DRAM modules, and M.2 NVMe SSD.

REQUIRED ITEMS (NOT INCLUDED)

• No power supply included – 15VDC/4A power supply required
• No RAM pre-installed – DDR4 SODIMM
• DDR3/DDR5 is not supported
• No eMMC Module or SSD included 
  
• M.2 SATA SSD is not supported (only NVMe SSD)
  
• No case included
• No HDMI cable included – needed to connect to a display device. Recommend HDMI2.0 cable to support 4K output

SPECIFICATIONS

Processor: 

• Intel Celeron N5105(H3+: N6005) Processor (10nm, Quad-Core, TDP 10W)
• H3(N5105) : up to 2.9GhzH3+(N6005) : up to 3.3Ghz
• 4MB L2 Cache
• Intel UHD Graphics (24/32 EU up to 900MHz)

Memory: 

• 2 x DDR4 1.2V SO-DIMM slots, Dual Channel, up to 2933 MT/s (DDR4-PC23400)
• Max memory capacity 64GB
• DDR3/DDR5 are not supported

Storage: 

• 1 x eMMC connector (bootable and selectable on BIOS)
• 2 x SATA3 6Gbps
• 1 x M.2 slot (PCIe 3.0 x 4, supports NGFF-2280 cards)
• M.2 SATA SSD is not supported

Networking:

• 2 x GbE LAN ports (RJ45, supports 10/100/1000/2500 Mbps)
• Realtek RTL8125B
• Supports Wake-On-Lan
• LED indicators (Green: Link, Amber: Traffic)

Video: 

• 1 x DisplayPort 1.2 (up to 4K@60Hz)
• 1 x HDMI 2.0 (up to 4K@60Hz)
• Dual simultaneous display support

Audio:

• 1 x Audio out (3.5mm jack)
• 1 x Audio in (3.5mm jack)
• 1 x SPDIF out (ALC1200, HDA codec)
• * HDMI & DP have audio output too.

External I/O:

• 2 x USB 3.0 Host ports
• 2 x USB 2.0 Host ports
• 1 x Peripheral Expansion Header (24-pin, 2.54mm pitch)
• 1 x DC 5V, 1 x DC 3.3V, 5 x GND
• 1 x UART (TXD/RXD/RTS/CTS)
• 2 x I2C (SCL/SDA)
• 1 x External Power Button
• HDMI CEC, 5VA+
• Three USB 2.0 ports
• All 3.3V I/O signal level

Other Features:

• Passive Heatsink
• BIOS Backup Battery
• Maintains system time and BIOS settings
• Power Button
• Reset Button
• System LEDS Indicators:
• Red (PWR) – Solid light when DC power is supplied
• Blue (left, SLEEP) – turns off only when the system enters into suspend mode
• Blue (right, PMIC) – turns on only when the major power rails are working
• Amber (SATA) – Flashes when SATA data transfers
• Green (NVMe) – Flashes when NVMe data transfers
• Active Cooling Fan Connector (12V 4-pin, PWM input + TACHO output)
• Active Cooling Fan is optional
• Connector (4-pin, 2.54mm pitch)

Power:

• DC jack : outer (negative) diameter 5.5mm, inner(positive) diameter 2.1mm
• DC 14V ~ 20V (up to 60W)
• DC 15V/4A power adapter is recommended if you don’t use two 3.5“ HDDs
• DC 19V/7A power adapter is recommended if you two 3.5” HDDs together
• Power consumption:
• IDLE : ≃1..9W
• CPU Stress : ≃15W
• CPU+GPU Stress : ≃18W
• Power-off : ≃0.25W
• Suspend : ≃0.6W

Form Factor:

• 110mm x 110mm x 47mm Approx.

• A. CPU (Intel Celeron N5105)
• B. 2 x DDR4 SO-DIMM slots (Dual channel memory support)
• C. 1 x M.2 PCI Express Module Socket (NGFF-2280)
• D. 1 x eMMC (Embedded Multimedia-Card) Socket
• E. 2 x SATA Power Connectors (2.5mm pitch, JST-XH compatible connector)
• F. 2 x SATA3 6.0 Gb/s Data Connectors
• G. 1 x DC Power Jack
• H. 2 x USB 3.0
• I. 2 x USB 2.0
• J. 1 x HDMI 2.0
• K. 1 x DisplayPort 1.2
• L. 2 x RJ45 Ethernet Ports (10/100/1000/2500)
• M. 5 x System LED Indicators
• N. 1 x Peripheral Expansion Header (24-pin)
• O. 1 x Power Switch
• P. 1 x Reset Switch
• Q. 1 x Backup Battery Connector (2-pin)
• R. 1 x Active Cooling Fan Connector (4-pin)
• S. 1 x Audio out, 1 x Audio in, 1 x SPDIF out

LINKS

• Installation – https://wiki.odroid.com/odroid-h3/start#installation
• WiKi – https://wiki.odroid.com/odroid-h3/start
• Introduction – https://dn.odroid.com/ODROID-H2/H3_pics/H3_H3+_Introduction.pdf

 VIDEOS